back to : SAMWAY P32Q hose crimper
User manual for the SAMWAY P32Q hose crimping press
Check also : hydraulic hose crimping manual ( full manual )
FIRST START-UP OF THE P32Q CRIMPER
Upon receiving the machine, unscrew the crimper and the die table from the pallet ( wrench no. 13 and 10). Next, unscrew the lifting eyes and the bolts used to secure the crimper ( 4 bolts per side wrench no. 13 or 14 and 19). After placing the bottom module in the workspace, lift the crimper using two straps or 40x40 square tubes. The greater weight of the crimper is on the head side. This task requires at least 4 people. The weight should be distributed evenly on the sides, remembering not to pull by the head. After placing the upper part on the die module, bolt the whole together ( 4 bolts per side). Next, connect the crimper to the power source using the cable ( 16A plug - 5 pins). Remove the protection from the oil filler cap ( zip tie with a cloth) and start the machine. Please pay attention to the motor's rotation direction ( clockwise rotation). When using lifting eyes (ears), pay attention during lifting so that the machine does not rotate. The overload protection on the distribution board must be at least 16A. Before the first operation, read the crimper's user manual and watch the instructional videos.
Crimping a DN10 2SN hose with P32Q crimper
Tip: During the first crimp, you must know what hose it is. There are markings of their parameters on the hoses. If you cannot read the values on the hose, first measure using calipers the internal diameter of the hose. Then visually determine how many steel windings, so-called braids, it has inside. Next, select the appropriate ferrule and hose fitting. Then check in the approximate crimping table for the dimension the hose is to be crimped to. Example: DN 10 mm ( 3/8 inch) 2SN hose - double-braided hose. Knowing the hose parameters, we look in the approximate crimping table for the value to which we should crimp the hose. For a DN 10 2SN hose, we read the value 20.6 mm in the table.
Selection of appropriate crimping dies
Next, we select the dies closest to the 20.6 mm parameter, applying the rule that the die size must be smaller than the 20.6 mm value. In this case, these are 19 mm dies. Then, using a simple mathematical operation, i.e., 20.6 mm - 19 mm = 1.6 mm. The difference after subtracting these values gives us the parameter to be set on the micrometer, which in this case is 1.6 mm. After fitting the number 19 dies, we proceed to set the value of 1.6 mm on the micrometer. Use the micrometer dial to set the desired value. The micrometer should be zeroed before setting. Zeroing consists of setting the dial in a position where the digit 0 aligns with the digit 0. By turning the micrometer dial to the right, we set 1.6 mm and proceed to crimp the hose. The upper digit on the micrometer will indicate 1, while the lower digit on the dial will indicate 60. Remember to crimp the ferrule on the hose twice. During the first crimp, a ridge is formed on the ferrule, which we must eliminate through a subsequent crimp. We do this by rotating the ferrule on the hose so that the dies press down on the ridge formed in that spot.
Micrometer setting in the P32Q crimper for DN10 2SN hose
Tip: Try not to engage the lock on the micrometer. After pressing the lock ( a small black protruding plastic clip), you lock the micrometer to the desired value. It very often happens that after turning on the lock, the next person operating the machine does not notice this detail and turns the micrometer by force, damaging it.
Potentiometer setting when opening the dies
Tip: Using the potentiometer, we can set the maximum or minimum opening range of the main dies in the head. When connecting the foot pedal to the crimper, make sure that the dot indicating the connection direction enters parallel to the socket in the machine marked in the same way. This will prevent the pins from bending.
Tip: There is HV-46 oil in the tank at the bottom of the machine. The manufacturer recommends working in positive temperatures. It is recommended to change the oil once a year. The oil drain bolt at the bottom of the tank is used for this purpose. After draining the used oil, the tank should be filled with new HV-46 oil in an amount of approximately 35-38 liters.