Skip to main content


Fluid power hydraulics - parts, accesories

Experienced Polish manufacturer & direct distributor of hydraulic components   
Retail & Wholesale – One-Stop Industrial Supplier | 100% European-owned    
   

six-time winner
Business Gazelles 2024

NATO supplier
Code 99Q4H
HYDRON NCAGE code

proven reliability
HYDRON DUNS number

authorized
service
Authorized ENERPAC Service Center in Poland

official
distributorUSA
Authorized ENERPAC distributor in Poland

official distributorEU SEMPERIT distributor

quality assurance
ISO 9001, TUV
HYDRON ISO certificates

📦 15,000+ items in our stock & ready to ship
⚡ Fast shipping 🛡️ Quality guarantee 🛠️ Technical support
Products in the cart: 0. See details
Your cart is empty

P32Q crimping machine user manual

back to : SAMWAY P32Q hose crimper

User manual for the SAMWAY P32Q hose crimping press 

See also : hydraulic hose crimping instructions ( full manual )

FIRST START-UP OF THE P32Q CRIMPING MACHINE

After receiving the machine, unscrew the crimper and the table with dies from the pallet (wrenches size 13 and 10). Next, unscrew the lifting eyes and the bolts used for screwing down the crimper (4 bolts per side, wrench size 13 or 14 and 19). After placing the bottom module at the workstation, lift the crimper using two straps or 40x40 square pipes. The main weight of the crimper is on the head side. At least 4 people are needed for this task. The weight should be distributed evenly on the sides, remembering not to pull by the head. After mounting the top part on the module with dies, screw the whole unit together (4 bolts per side). Next, connect the crimper via cable to the power source (16Ah plug - 5 pins). Remove the protection from the oil filler cap (cable tie with a cloth) and start the machine. Please pay attention to the motor rotation direction (clockwise rotation). When using mounting handles (eyes), pay attention during lifting so that the machine does not rotate. The overload protection on the switchboard must be at least 16A. Before the first operation, read the crimper's user manual and watch instructional videos.

Crimping a DN10 2SN hose with the P32Q crimper

Tip: During the first crimping, you must know what hose it is. There are markings of their parameters on the hoses. If you cannot read the values on the hose, first measure with calipers the inner diameter of the hose. Then visually determine how many steel wire reinforcements, so-called braids, it has inside. Next, select the appropriate ferrule and hose fitting. Then check in the approximate crimping table to what dimension the hose is to be crimped. Example: DN 10 mm (3/8 inch) 2SN hose - double-braided hose. Knowing the hose parameters, we look in the approximate crimping table for the value to which we should crimp the hose. For a DN 10 2SN hose, we read the value 20.6 mm in the table.

Selecting the appropriate crimping dies  

Next, we select the dies closest to the 20.6 mm parameter, applying the rule that the die size must be smaller than the 20.6 mm value. In this case, these are 19 mm dies. Next, using a simple mathematical operation, i.e., 20.6 mm - 19 mm = 1.6 mm. The difference after subtracting these values gives us the parameter we need to set on the micrometer, which in this case is 1.6 mm. After fitting the number 19 dies, we proceed to set the value of 1.6 mm on the micrometer. Use the micrometer knob to set the desired value. The micrometer should be zeroed before setting. Zeroing consists of setting the knob to a position where the digit 0 aligns with the digit 0. By turning the knob of the micrometer to the right, we set 1.6 mm and proceed to crimp the hose. The top digit on the micrometer will indicate 1, while the bottom digit on the knob will indicate 60. Remember to crimp the ferrule on the hose twice. During the first crimping, a ridge is formed on the ferrule, which we must eliminate through subsequent crimping. This operation is performed by rotating the ferrule on the hose so that the dies press down on the ridge formed in that place.

 

Setting the micrometer in the P32Q crimper for DN10 2SN hose

Tip: Try not to engage the lock on the micrometer. After pressing the lock (small black protruding plastic clip), you lock the micrometer to the desired value. It very often happens that after engaging the lock, the next person operating the machine does not notice this detail and turns the micrometer by force, damaging it. 

Setting the potentiometer when opening the dies

Tip: Using the potentiometer, we can set the range of maximum or minimum opening of the main dies in the head. When connecting the foot pedal to the crimper, make sure that the dot indicating the connection direction enters parallel to the socket in the machine marked in the same way. This will prevent pins from bending. 

Tip: In the tank at the bottom of the machine, there is HV-46 oil. The manufacturer recommends working in positive temperatures. It is recommended to change the oil once a year. The oil drain plug at the bottom of the tank is used for this purpose. After draining the used oil, fill the tank with new HV-46 oil in the amount of approximately 35-38 liters.