Skip to main content


Fluid power hydraulics - parts, accesories

Experienced Polish manufacturer & direct distributor of hydraulic components   
Retail & Wholesale – One-Stop Industrial Supplier | 100% European-owned    
   

six-time winner
Business Gazelles 2024

NATO supplier
Code 99Q4H
HYDRON NCAGE code

proven reliability
HYDRON DUNS number

authorized
service
Authorized ENERPAC Service Center in Poland

official
distributorUSA
Authorized ENERPAC distributor in Poland

official distributorEU SEMPERIT distributor

quality assurance
ISO 9001, TUV
HYDRON ISO certificates

📦 15,000+ items in our stock & ready to ship
⚡ Fast shipping 🛡️ Quality guarantee 🛠️ Technical support
Products in the cart: 0. See details
Your cart is empty

User manual for the P32Q crimping machine

back to : SAMWAY P32Q hose crimping machine

User manual for the SAMWAY P32Q hose crimping press 

Also check : hydraulic hose crimping manual ( full manual )

FIRST START-UP OF THE P32Q CRIMPING MACHINE

After receiving the machine, unscrew the crimper and the die table from the pallet ( wrench sizes 13 and 10). Next, unscrew the mounting lugs and the bolts used for screwing down the crimper ( 4 bolts per side, wrench sizes 13 or 14 and 19). After positioning the lower module at the workstation, lift the crimping machine using two straps or 40x40 square tubes. Most of the crimper's weight is on the head side. At least 4 people are needed for this task. The weight should be distributed evenly on the sides, remembering not to pull by the head. After placing the upper part on the die module, bolt everything together ( 4 bolts per side). Next, connect the crimper to the power source using the cable ( 16Ah plug - 5 pins). Remove the protection from the oil filler cap ( zip tie with a cloth) and start the machine. Please pay attention to the direction of motor rotation ( clockwise rotation). When using mounting brackets ( lugs), pay attention during lifting so that the machine does not rotate. The overload protection on the distribution board must be at least 16A. Before the first operation, read the crimper's user manual and watch the instructional videos.

Crimping a DN10 2SN hose with the P32Q crimper

Tip: During the first crimp, you must know what kind of hose it is. Hoses have their parameter markings on them. If you cannot read the values on the hose, first measure with calipers the internal diameter of the hose. Then visually determine how many steel wire reinforcements ( the so-called braids) it has inside. Next, select the appropriate ferrule and hose fitting. Then check the approximate crimping chart for what dimension the hose is to be crimped. Example: DN 10 mm hose ( 3/8 inch) 2SN - double-braided hose. Knowing the hose parameters, we look in the approximate crimping chart for the value to which we should crimp the hose. For a DN 10 2SN hose, we read the value of 20.6 mm in the chart.

Selecting the appropriate crimping dies  

Next, we select the dies closest to the 20.6 mm parameter, using the rule that the die size must be smaller than the value of 20.6 mm. In this case, these are 19 mm dies. Next, applying a simple mathematical operation, i.e. 20.6 mm - 19 mm = 1.6 mm. The difference after subtracting these values gives us the parameter to be set on the micrometer, which in this case is 1.6 mm. After installing the number 19 dies, we proceed to set the value of 1.6 mm on the micrometer. Use the micrometer dial to set the desired value. The micrometer should be zeroed before setting. Zeroing consists of setting the dial to the position where the number 0 aligns with the number 0. By turning the micrometer dial to the right, we set 1.6 mm and proceed to crimp the hose. The upper digit on the micrometer will indicate 1 while the lower one on the dial will indicate 60. Remember to crimp the ferrule on the hose twice. During the first crimp, a ridge forms on the ferrule, which we must eliminate by a subsequent crimp. This is done by rotating the ferrule on the hose so that the dies press down on the ridge formed at that spot.

 

Micrometer setting in the P32Q crimper for DN10 2SN hose

Tip: Try not to turn on the lock on the micrometer. After pressing the lock ( a small black protruding plastic clip), you lock the micrometer to the desired value. It very often happens that after turning on the lock, the next person operating the machine does not notice this detail and turns the micrometer by force, damaging it. 

Potentiometer setting for die opening

Tip: Using the potentiometer, we can set the range of maximum or minimum opening of the main dies in the head. When connecting the foot pedal to the crimper, make sure the dot indicating the connection direction enters parallel to the socket in the machine marked in the same way. This will prevent the pins from bending. 

Tip: There is HV-46 oil in the tank at the bottom of the machine. The manufacturer recommends working in positive temperatures. It is recommended to change the oil once a year. The oil drain bolt at the bottom of the tank is used for this purpose. After draining the used oil, the tank should be filled with new HV-46 oil in an amount of approximately 35-38 liters.