Skip to main content


Fluid power hydraulics - parts, accesories

Experienced Polish manufacturer & direct distributor of hydraulic components   
Retail & Wholesale – One-Stop Industrial Supplier | 100% European-owned    
   

six-time winner
Business Gazelles 2024

NATO supplier
Code 99Q4H
HYDRON NCAGE code

proven reliability
HYDRON DUNS number

authorized
service
Authorized ENERPAC Service Center in Poland

official
distributorUSA
Authorized ENERPAC distributor in Poland

official distributorEU SEMPERIT distributor

quality assurance
ISO 9001, TUV
HYDRON ISO certificates

📦 15,000+ items in our stock & ready to ship
⚡ Fast shipping 🛡️ Quality guarantee 🛠️ Technical support
Products in the cart: 0. See details
Your cart is empty

User manual for the P18HP portable crimping machine

back to : manual crimping machines

User manual of the SAMWAY P18HP mobile crimper

P18HP manual crimper - instruction for mobile hydraulic hose crimper

Installing and removing dies P18HP crimper

Tip: Choose the dies closest to the hose being crimped. Example: Hose DN10 mm 3/8 inch 2SN double-braided. Having the hose size and the number of steel braids, we check in the approximate crimping table what value the hose is to be crimped to. In this case, 20.6 mm. Then use the closest dies below the value of 20.6 mm. In this case, these are dies numbered 19. 

Micrometer setting P18 crimper

Tip: Before setting the desired value, make sure the micrometer is zeroed. I.e. whether 0 on the dial aligns with 0 on the handle. Remember not to turn the micrometer below the value 0. This can damage it. We set the micrometer by turning the micrometer dial to the right. 

Bleeding the pump in the P18HP crimper

Tip: During crimping, set the cap knob to the Vent position. For transport, turn the cap to the Close position. In the case of unscrewing the pump with the wing nut, pay attention whether oil is escaping from under the cap. If you notice a leak, tighten it gently. Try to ensure that after each use of the pump, the system is completely bled. You bleed the system by completely loosening the oil filler cap. 

Hose crimping P18 crimper

Tip: During the first crimp, you must know what hose it is. On the hoses there are markings of their parameters. If you cannot read the value on the hose, first measure the inner diameter of the hose with a caliper. Then visually determine how many steel coils, so-called braids, it has inside. Next, select the appropriate ferrule and hose fitting. Then check in the approximate crimping table what dimension the hose is to be crimped to. 

EXAMPLE: Hose DN 10 mm ( 3/8 inch) 2SN - double-braided hose. Knowing the hose parameters, we look in the approximate crimping table for the value to which we are to crimp the hose. In the case of a DN 10 2SN hose, we read the value 20.6 mm in the table. Then we select the dies closest to the 20.6 mm parameter, applying the rule that the die size must be smaller than the value 20.6 mm. In this case, these are dies with a size of 19 mm. Next, using a simple mathematical operation, i.e., 20.6 mm - 19 mm = 1.6 mm. The difference after subtracting these values gives us the parameter we are to set on the micrometer, which in this case is 1.6 mm. After installing dies number 19 and setting the value 1.6 mm on the micrometer, we proceed to crimp the hose. Remember to crimp the ferrule on the hose twice. During the first crimp, a ridge is formed on the ferrule, which we must eliminate by a subsequent crimp. We perform this action by rotating the ferrule on the hose so that the dies press the ridge formed in that spot.