Skip to main content


Fluid power hydraulics - parts, accesories

Experienced Polish manufacturer & direct distributor of hydraulic components   
Retail & Wholesale – One-Stop Industrial Supplier | 100% European-owned    
   

six-time winner
Business Gazelles 2024

NATO supplier
Code 99Q4H
HYDRON NCAGE code

proven reliability
HYDRON DUNS number

authorized
service
Authorized ENERPAC Service Center in Poland

official
distributorUSA
Authorized ENERPAC distributor in Poland

official distributorEU SEMPERIT distributor

quality assurance
ISO 9001, TUV
HYDRON ISO certificates

📦 15,000+ items in our stock & ready to ship
⚡ Fast shipping 🛡️ Quality guarantee 🛠️ Technical support
Products in the cart: 0. See details
Your cart is empty

Assembly instructions for cutting rings

back to : fittings for connecting precision tubes

Mounting cutting rings on a tube

Cutting ring assembly instructions

1. Cut the tube at a right angle. A deviation of 0.5º from the right angle is permissible.
2. Remove internal and external burrs (you can use a deburring tool ) 
3. For thin-walled tubes as well as those made of aluminum or copper, reinforcement sleeves should be used.
4. Minimum lengths of the straight tube section must be maintained according to the table below.

cutting ring assembly instructions

Series

LL

L

S

tube ext. diameter

4

5

6

8

6

8

10

12

15

18

22

28

35

42

6

8

10

12

14

16

20

25

30

38

H min.

24

25

25

26

31

31

33

33

36

38

42

42

48

48

35

35

37

37

43

43

50

54

58

65

L min.

30

32

32

33

39

39

42

42

45

48

53

53

60

60

44

44

47

47

54

54

63

68

73

82

LUBRICATION

All our fittings are coated with a colorless lubricant. Additional lubrication of fittings with diameters smaller than 20 mm is not necessary. In case of disassembly and reassembly, the fittings should be oiled.

ASSEMBLY USING WRENCHES (for single and double-edged rings)

1. Slide the ring and nut onto the tube according to the diagram below.
2. Tighten the nut manually until hand-tight.
3. Pressing the tube against the stop in the connector, tighten the nut with a wrench by approximately 1.1/4 to 1.1/2 turns.
4. Bite check: Unscrew the nut and check if a collar covering the front part of the cutting edge has appeared. Rotation of the ring is permissible, but the ring must not move along the tube.
Reassembly: if the ring bite is correct, tighten the nut with the same force as during initial assembly. To achieve this, tighten the nut manually until hand-tight, then using a wrench, tighten by approximately 1/4 turn.

assembly of a cutting ring on a hydraulic tube

ASSEMBLY IN A VICE USING A PRE-ASSEMBLY DIE

Lubricate the thread and the working part of the assembly die
1. Slide the ring and nut onto the tube according to the diagram below.
2. Tighten the nut manually until hand-tight.
3. Pressing the tube against the stop in the die, tighten the nut with a wrench by approximately 1.1/4 turns.
4. Pre-assembly bite check: Unscrew the nut and check if a collar covering the front part of the cutting edge has appeared. Rotation of the ring is permissible, but the ring must not move along the tube.

Final assembly using the fitting body:
5. Tighten the nut manually until hand-tight.
6. Tighten the nut by approximately 1/4 turn.

tightening a fitting on a tube with a ring - connecting tubes without welding

ASSEMBLY USING A PRE-ASSEMBLY CUTTING RING DEVICE

1. Select the appropriate die and support plate, consistent with the tube diameter and fitting series.
2. Slide the ring and nut onto the tube according to the diagram below.
3. Place the tube with the ring and nut in the device between the die and the support plate.
4. Press the tube against the die stop.
5. Hold the tube steady in a position perpendicular to the device. Press and hold the START button until the pre-assembly process is automatically completed.
6. After the process is complete, remove the tube from the device.
7. Check if a collar covering the front part of the cutting edge has appeared. Rotation of the ring is permissible, but the ring must not move along the tube.


Final assembly: Tighten the nut manually until hand-tight, then with a wrench by approximately 1/4 turn.

device for mounting cutting rings on a tube

SYSTEM DESCRIPTION

Cutting ring fittings provide easy and quick assembly of pipelines, guaranteeing a high level of installation safety.

The fitting consists of a body, a cutting ring, and a special nut. Depending on the pressure, three series of components are available: LL series for lowest pressures, L series for medium, and S series for highest pressures.

CUTTING RINGS

Double-edged ring (for L and S series) – is a standard ring offering very good connection tightness and compatibility with fittings according to DIN 2353. During assembly, the two cutting edges (1 and 2), thanks to their geometry sliding along the cone (3), bite into the tube surface creating a visible metal collar (5) covering the front cutting edge. Edge (1) bites into the tube earlier than edge (2), and after the bite, surface (6) blocks further edge penetration into the tube. The contact surface (4) provides additional tube support.

Single-edged ring (for LL series) – is a ring intended for low-pressure installations (maximum 100 bar). During assembly, the cutting edge (1) sliding along the cone bites into the tube surface creating a visible metal collar (4) covering the front part of the edge. The tube must be pushed against the fitting stop (2).

 

 

Example of a mounted ring on a hydraulic tube 

cutting ring mounted on a tube